DueProLogic 알테라 사이클론 4 EP4CE6E22 USB FPGA
(DueProLogic USB-FPGA -Intel/Altera Cyclone IV EP4CE6E22)
개요
- 본 제품은 DueProLogic USB-FPGA 개발 플랫폼입니다.
- 강력한 Altera Cyclone IV FPGA, 고속 USB 인터페이스 칩, Full SD 카드 인터페이스, 4MB confiration Flash를 지원합니다.
- USB 인터페이스 칩은 듀얼 채널 FT2232H 입니다. 한개의 채널은 FPGA 설정 플래쉬 로딩 전용으로 할당되어 있으며, 나머지 채널은 FPGA와 양방향으로 고속 통신을 하기 위해 제공됩니다.
- DHL 코드를 만들고 플래쉬에 프로그래밍하여 PC에서 하드웨어와 통신할 수 있습니다.
- 아두이노 두에 폼팩터로 디자인되었으며, 제품을 이용하여 디지털 디자인과 로직 디바이스를 실험하여 볼수 있습니다.
- 스텝 바이 스텝 형식으로 설명하여 놓은 사용자 매뉴얼을 지원합니다.
특징
- The DPL’s FPGA is a 144 pin Altera Cyclone IV /E that is
configured to operate with a 66MHz clock for synchronizing
circuits, should you want to. With the addition of a
supplemental oscillator, a 100MHz or other compatible
oscillator can be added. - Model EP4CE6E22C8N, operating internally with 1.2V and
2.5V, and exteranally at 3.3V being 3.3V tolerant - Operates corner to corner logic in 9ns
- 392 configurable logical/logic array blocks, 6272 logical
elements/cells, 270Kbit internal RAM, 15 multipliers to support DSP
processing-intensive applications, 2 PLLs - When not powered, your last running project is stored in
an ample 4Mb serial memory chip. The project is automatic-
ally reloaded at power-on. - A board LED (labeled CONF DONE) indicates the board is
running your project. - Board Layout: (pictures below)
- The first connection you use for the PDL is the single
micro-USB-B from your PC. It uses a full USB 2.0 (480Mb/s)
connection through the on-board dual-engine FTDI FT2232H
chip for both active-serial programming the Cyclone and
8-bit wide communication with a running Cyclone
application, allowing for high speed two-way project
communication between the Cyclone and PC. This connection
is considerably faster than all other known development
boards on the market. - Stackable Headers surround the DPL:
- Silkscreen labels the headers to facilitate jumper
wire connections and positioning mini-modules - The headers are higher than all other board components
so that nothing is in the way of using the headers - Standard Arduino shield (3.3v tolerant only) layout with
18 pins on the headers connected to the Cyclone. (not pictured) - Headers match those of the Arduino Due, including its
2x36 pin header and three center SPI header pins, having
connection to 61 pins on the Cyclone. - An additional 2x40 right angle header allowing the DPL
to be plugged directly into a standard 0.1” pitch
breadboard, both supporting the DPL on your project board(s)
and simplifying the wiring to your external 3.3V project-
related components.
문서
-
85-000012 DUEPROLOGIC FPGA DEVELOPMENT SYSTEM USER MANUAL DPL_FPGA_DEV_SYS_UM.PDF 95-000012 DUEPROLOGIC FPGA DEVELOPMENT SYSTEM DATA SHEET DPL_FPGA_DEV_SYS_DS.PDF 45-000012 DUEPROLOGIC FPGA DEVELOPMENT SYSTEM PROJECT DVD DUEPROLOGIC FPGA PROJECT DVD 55-000012 ARDUINO DUE FPGA DEVELOPMENT SYSTEM SCHEMATICS EPT-DPL-USB-FPGA-SCHEMATICS.PDF 35-000001 EPT DRIVERS EPT_2.08.24.ZIP
