DueProLogic 알테라 사이클론 4 EP4CE6E22 USB FPGA

(DueProLogic USB-FPGA -Intel/Altera Cyclone IV EP4CE6E22)

개요

  • 본 제품은 DueProLogic USB-FPGA 개발 플랫폼입니다.
  • 강력한 Altera Cyclone IV FPGA, 고속 USB 인터페이스 칩, Full SD 카드 인터페이스, 4MB confiration Flash를 지원합니다.
  • USB 인터페이스 칩은 듀얼 채널 FT2232H 입니다. 한개의 채널은 FPGA 설정 플래쉬 로딩 전용으로 할당되어 있으며, 나머지 채널은 FPGA와 양방향으로 고속 통신을 하기 위해 제공됩니다.
  • DHL 코드를 만들고 플래쉬에 프로그래밍하여 PC에서 하드웨어와 통신할 수 있습니다.
  • 아두이노 두에 폼팩터로 디자인되었으며, 제품을 이용하여 디지털 디자인과 로직 디바이스를 실험하여 볼수 있습니다.
  • 스텝 바이 스텝 형식으로 설명하여 놓은 사용자 매뉴얼을 지원합니다.

특징

  • The DPL’s FPGA is a 144 pin Altera Cyclone IV /E that is
    configured to operate with a 66MHz clock for synchronizing
    circuits, should you want to. With the addition of a
    supplemental oscillator, a 100MHz or other compatible
    oscillator can be added.
  • Model EP4CE6E22C8N, operating internally with 1.2V and
    2.5V, and exteranally at 3.3V being 3.3V tolerant
  • Operates corner to corner logic in 9ns
  • 392 configurable logical/logic array blocks, 6272 logical
    elements/cells, 270Kbit internal RAM, 15 multipliers to support DSP
    processing-intensive applications, 2 PLLs
  • When not powered, your last running project is stored in
    an ample 4Mb serial memory chip. The project is automatic-
    ally reloaded at power-on.
  • A board LED (labeled CONF DONE) indicates the board is
    running your project.
  • Board Layout: (pictures below)
  • The first connection you use for the PDL is the single
    micro-USB-B from your PC. It uses a full USB 2.0 (480Mb/s)
    connection through the on-board dual-engine FTDI FT2232H
    chip for both active-serial programming the Cyclone and
    8-bit wide communication with a running Cyclone
    application, allowing for high speed two-way project
    communication between the Cyclone and PC. This connection
    is considerably faster than all other known development
    boards on the market.
  • Stackable Headers surround the DPL:
  • Silkscreen labels the headers to facilitate jumper
    wire connections and positioning mini-modules
  • The headers are higher than all other board components
    so that nothing is in the way of using the headers
  • Standard Arduino shield (3.3v tolerant only) layout with
    18 pins on the headers connected to the Cyclone. (not pictured)
  • Headers match those of the Arduino Due, including its
    2x36 pin header and three center SPI header pins, having
    connection to 61 pins on the Cyclone.
  • An additional 2x40 right angle header allowing the DPL
    to be plugged directly into a standard 0.1” pitch
    breadboard, both supporting the DPL on your project board(s)
    and simplifying the wiring to your external 3.3V project-
    related components.

문서

연관제품