블레이드RF x115 SDR -USB3.0 슈퍼 스피드 소프트웨어 정의 라디오
(bladeRF x115 - USB 3.0 SuperSpeed Software Defined Radio)
개요
- 본 제품은 bladeRF x115 USB 3.0 소프트웨어 정의 라디오(SDR) 장치입니다.
- 추가 장치 없이 300Mhz에서 3.8Ghz까지 주파수 튜닝이 가능하며, GNURadio (live image) 와 같은 오픈소스 소프트웨어를 이용하여 바로 사용이 가능합니다.
- bladeRF x40이 40KLE Cyclone 4 FPGA를 탑재한 것과는 다르게 115KLE Cyclone 4 FPGA를 탑재하여 hardware accelerator 및 FFT, 터보 디코더, transmit modulator/filter, acquisition correlators for burst modems 을 포함한 신호 처리 체인을 위한 추가적인 기능을 제공합니다.
- 빠른 USB 3.0을 사용하여 넓은 라디오 대역폭을 위한 컴퓨터 인터페이스를 제공하며,
- 유연한 하드웨어 및 소프트웨어 특성을 이용하여 bladeRF를 사용자 RF 모뎀이나, GSM/LTE picocell, GPS 리시버, ATSC 트랜스미터 혹은 블루투스/WiFi 클라이언트로 동작하게 설정할 수 있습니다.
- 모든 bladeRF host software, firmware, HDL은 오픈 소스로 다음의 Github에서 확인할 수 있습니다. available on GitHub
특징
- Full-duplex 40MSPS 12bit quadrature sampling
- Factory calibrated VCTCXO tuned within 1 Hz of 38.4 MHz
- Removable-cap RF shields for increased system sensitivity and isolation
- Flexible clocking architecture for arbitrary sample rates
- GPIO expansion port ( GPIO Expansion Board )
- SPI flash allows for headless operation
- Expanded frequency coverage using XB-200 Transverter Board
- Typical +6dBm TX power
- Fully bus-powered USB 3.0 SuperSpeed Software Defined Radio
- Portable, handheld form factor: 5" by 3.5"
- Extensible gold plated RF SMA connectors
- 300MHz - 3.8GHz RF frequency range
- Independent RX/TX 12-bit 40MSPS quadrature sampling
- Capable of achieving full-duplex 28MHz channels
- 16-bit DAC factory calibrated 38.4MHz +/-1ppm VCTCXO
- On-board 200MHz ARM9 with 512KB embedded SRAM (JTAG port available)
- On-board 115KLE Altera Cyclone 4 E FPGA (JTAG port available)
- 2x2 MIMO configurable with SMB cable, expandable up to 4x4
- Modular expansion board design for adding GPIO, Ethernet, and 1PPS sync signal and expanding frequency range, and power limits
- DC power jack for running headless
- Highly efficient, low noise power architecture
- Stable Linux, Windows, Mac and GNURadio software support
- Hardware capable of operating as a spectrum analyzer, vector signal analyzer, and vector signal generator
- Kit includes:
- bladeRF x115 (115KLE Cyclone 4 FPGA)
- USB 3.0 SS cable
- 2x SMA cables