LTE Cat 4 이동통신 데이터 모듈 -LARA-L6004D

(LTE CAT.4 3 CLICK - DATA)

   

개요

  • 본 제품은 LTE Cat 4 이동통신 데이터 모듈 -LARA-L6004D 모듈입니다.
  • ublox사의 LARA-L6004D-01B 모듈을 기반으로 디자인된 제품으로 LTE Cat 4 FDD 및 LTE Cat 4 TD 를 지원합니다.
  • 글로벌하게 데이터 통신을 하고자하는 어플리케이션에 사용이 가능하며, UART 인터페이스를 가지고 있습니다.

특징

  • HOW DOES IT WORK?

    LTE Cat.4 3 Click is based on the LARA-L6004D-01B, an LTE Cat 4 module in the smallest form factor from u-blox. This data-only module supports DualStack IPv4/IPv6, FOAT/uFOTA, LwM2M, jamming detection, and more. It operates as a four-band device in a frequency range of 700MHz up to 2600MHz. There are two SMA antenna connectors to which you should connect the appropriate antennas that MIKROE offers. The ANT1 antenna is a primary one that supports both TX and RX, while the ANT2 one only supports RX for the LTE Down-Link MIMO 2x2 and 3G RX diversity configuration.

    lte-cat.4 3 click inner img

    The LTE Cat.4 3 Click is equipped with a nano SIM card holder for both 1.8V and 3.0V SIM types. The module also includes a USB high-speed 2.0-compliant interface with a minimum 480Mbps data rate. The module itself acts as a USB device and can be connected to any compatible USB host. It provides a virtual serial port over USB for AT commands and communication, a virtual serial port over USB for diagnostic logs, and more.

    LTE Cat.4 3 Click uses a standard 2-wire UART interface to communicate with the host MCU, with commonly used UART RX and TX supporting up to 3000000bps (115200 is the default). The hardware flow control functionality is also available over the RTS and CTS pins. The data transmission is also visualized over the TX LED. Besides the library we provide, you can also use a set of AT commands to communicate with the module. The network status is available over the STS pin and the STATUS LED. The module can be powered off through the software, AT commands, or over the PWR pin. The module uses the TXB0106 and the PCA9306, bidirectional translators from Texas Instruments, for logic-level translation. The I2C interface is also available for communication with the host MCU with optional pull-up resistors.

    This Click board™ can operate with either 3.3V or 5V logic voltage levels selected via the VCC SEL jumper. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. Also, this Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used as a reference for further development.

    SPECIFICATIONS

    Type 3G UMTS,GSM+GPS,LTE IoT
    Applications Can be used for the development of asset tracking, telematics, remote monitoring, alarm panels, video surveillance, and more
    On-board modules LARA-L6004D-01B - LTE Cat 4 module in the smallest form factor from u-blox
    Key Features Multi-bend and multi-mode module, supports LTE Cat 4 FDD, LTE Cat 4 TDD radio access technology (RTA), 3G UMTS/HSPA, 2G GSM/GPRS/EGPRS, data-only communication, wide operating frequency range, long list of security features, FOAT, DNS, PPP, and more
    Interface I2C,UART,USB
    ClickID No
    Compatibility mikroBUS™
    Click board size L (57.15 x 25.4 mm)
    Input Voltage 3.3V or 5V

문서

연관제품