아트 컨트롤러- 타이밍 릴레이 키트
(Art Controller - Relay Board Kit)
개요
- 아트 컨트롤러는 다재다능한 stand-alone 릴레이 모듈로 24VDC 및 40VAC까지의 부하를 스위칭 할 수 있습니다.
- 이 제품이 다른 릴레이 모듈과 다른 점은 ATtiny2313 마이크로컨트롤러를 이용하여 릴레이 동작 타이밍을 설정할 수 있다는 점입니다.
- 버튼이 눌린 뒤 혹은 동전투입기에 동전이 투입된 후, 약간의 시간이 흐른 후에 동작하는 전자 예술품을 동작시키거나 하는데 사용이 가능하여 아트 컨트롤러라 이름이 붙여 지게 되었습니다.
- 보드상의 8-position DIP 스위치를 이용하여 프로그래밍 없이 1초에서 31시간까지의 타이밍을 설정할 수 있습니다.
- 본 제품은 키트형태의 제품으로 납땜 및 조립이 필요합니다.
-
Includes:
- 1x Art Controller PCB
- 1x ATtiny2313 Microcontroller
- 1x GSLA SPDT 5A Relay
- 1x 8-Position DIP Switch
- 1x 100uF 10V Capacitor
- 1x 10uF 50V Capacitor
- 1x 2N4401 Transistor
- 1x 1A Linear Regulator
- 1x 6-32 x 1/4" Screw
- 1x 6-32 Kep Nut
- 1x 6-pin Header
- 1x 20-pin Socket
- 1x Screw Terminal, 3-pos
- 2x Screw Terminal, 2-pos
- 2x 1N5817 Diode
- 2x Yellow LED, 3mm
- 3x 1K Resistor
- 3x 0.1uF 25V Capacitor
특징
- Hardware features:
- Recommended load rating: 24 V DC/40 VAC, 5 A (10 A, normally-open, only).
- Screw terminals for relay contacts.
- DIP switches to set timing.
- Power indicator and relay state indicator LEDs.
- On-board 5 V regulator; runs from 7-15 V DC, or can be run from 5 V directly.
- Screw terminals for trigger and input power. Location for optional DC power barrel jack.
- Preprogrammed AVR Microcontroller (Atmel ATtiny2313A), with 6-pin programming header
- Standard timing features:
- Time delay can be set from 1 second to 31 hours.
- Time delay is set by DIP switches; no need to guess and check timing with an adjustment dial.
- Auxiliary cancel-trigger input, halts operation immediately.
- Can be triggered by any low-going signal, or external button, switch, or coin acceptor.
- Versatile operating modes:
- Can be run as a one-shot or repeating (automatic cycling) timer.
- Can be configured to cancel the trigger if a second trigger input is received.
- Can be set to automatically trigger at power-on.
문서
- Schematic
- Datasheet (ATtiny2313)
- Datasheet (G5LA Relay)
- Assembly Instructions
- Art Controller Wiki
- Product Page
연관제품
- 연관제품 1