RF-Nano 아두이노 보드 -ATmega328, NRF24L01+, USB C

(RF-Nano -USB C, NRF24L01+)

 

개요

  • 본 제품은 RF-Nano 아두이노 보드 -ATmega328, NRF24L01+, USB C입니다.
  • ATmega328 칩을 기반으로 디자인된 아두이노 나노 폼팩터를 가지고 있으며, 2.4Ghz 원거리 통신이 가능한 NRF24L01+ 무선 트랜시버를 탑재한 제품입니다.
  • 원리 무선 통신이 필요한 어플리케이션에서 사용이 가능하며, 아두이노 IDE 환경에서 개발이 가능합니다.
  • USB C 커넥터를 장착하고 있습니다.

특징

  • Creative products, RF-Nano-Board: Upgraded nano board for arduino, The main chip is ATMEGA328P-MU QFN32,the latest bootloader (Arduino IDE 1.8.8) was burned down. It is fully compatible with the common nano board. RF-Nano-Board is PIN-PIN with Arduino Nano V3.0, and share the same codes.
  • More convenient for application: The RF-Nano-Board integrates a NRF24L01+ module with arduino nano v3.0 board, which is very convenient for 2.4G wireless connect application.
  • High quality material and Technology: We used high quality PCB original material and Immersion Gold Technology to make sure every board has smooth edge and more reliable.
  • Super small volume design, more convenient to use: The PCB size is only 48x19mm, the pin is fully compatible with Nano V3.0, No Soldering needed. The micro usb port is more convenient to use.
  • Complete Information reference: RF-Nano-Board using CH340 chip to UART, you can download mac, windows, linux three system drivers, datasheets and schematics and other informations from here
  • Microcontroller ATmega328P
    Nrf24L01+ 2.4G wireless
    Architecture AVR
    Operating Voltage: 5 V
    Flash Memory: 32 KB of which 2 KB used by bootloader
    SRAM: 2 KB
    Clock Speed: 16 MHz
    Analog I/O Pins: 8
    EEPROM: 1 KB
    DC Current per I/O Pins: 40 mA (I/O Pins)
    Input Voltage: 7-12 V
    Digital I/O Pins: 22
    PWM Output: 6
    Power Consumption: 19 mA
  • ◆ It is fully compatible with the nano-v3.0 pin and its usage method
    ◆ BLE chip: TI CC2540
    ◆ Work channel: 2.4G
    ◆ Transmission distance: 50m
    ◆ Supports AT directive to configure BLE
    ◆ Support USB virtual serial port, hardware serial port, BLE three-way transparent transmission
    ◆ Support master and slave switch
    ◆ Supports sending over 20byte.
    ◆ Supports iBeacons
    ◆ Interface: USB C
    ◆ Input voltage: USB power supply, Vin6~12V, 5V
    ◆ MCU: ATmega328P-MU QFN32
    ◆ Bootloader: Newest 1.8.8
    ◆ Pin: Two Lines 2.54mm-15Pin
    ◆ Size: 48mm x 19mm x 12mm
  • Note:

    Please use IDE 1.8.6 or higher version, First, install the CH340 driver, then follow this selection path in IDE: Tools -  Board“ Nano” Processor “ATmega328P",
    otherwise you'll find that you can't burn any program. 

문서


연관제품